You are here: Home > Products > medical Display > MMD-4300C
MMD-4300C

30" color TFT LCD

 
The 30" MMD-4300C integrates multiple viewing modes and color-to-grayscale technology, enabling flexible viewing options. MMD-4300C is ideal for 3D color rendering and image fusion applications. The MMD-4300C is also awarded by Taiwan Excellence 2008, the highest accolade awarded to products that encapsulate innovalue.
     Features
30" color TFT LCD
Resolution-2560(H) x 1600(V)
Max. luminance: 370cd/m2
  Max. calibrated luminance: 250cd/m2
GrayEasy® 30-bit deep color technology
Built-in front sensor for DICOM conformance and auto-dimming function
Selectable Gamma 1.8,2.0,2.2 and color temperature settings
Single 4MP and dual 2MP viewing mode setup
Smart OSD for easy monitor control
Intelligent display mode auto adjustment with graphic card auto detection
Intelligent color-to-gray conversion for grayscale applications
IPXX/IPX2 compliant
     Intelligent Color Display Solutions
GrayEasy® 30-bit Deep Color Technology
30-bit color image (10-bit for each RGB element) can be displayed on PACSmate® monitors without any image loss. Through IEIs unique GrayEasy® technology, it's unnecessary to replace the monitors for future HDMI™ 1.3 supported deep color display capabilities.
 
Multiple Viewing Modes and Color to Grayscale Technology
IEI has designed multiple viewing setups and color to grayscale technology into our 4MP MMD-4300C color display,bringing the intelligence and flexibility to your imaging workstation. Through color to grayscale technology,the RGB signal received can be accurately reproduced in grayscale via conversion function. IEI allows you to choose within a wide range of viewing modes for your PACS applications
Single Viewing Mode
In single viewing mode, the MMD-4300C is displayed as a single 4MP monitor, either in color or in grayscale mode.
Single 4MP in color mode Single 4MP in grayscale mode
Dual Viewing Mode
Through two DVI signal inputs, the MMD-4300C can be configured to display in a dual 2MP viewing mode. With color-to-grayscale conversion technology, the MMD-4300C can be viewed in multiple modes for side-by-side image comparison purpose. The independent Look-Up-Table for DICOM and Gamma calibration ensures the best display quality for diagnostic applications. The real-time adjustment of multiple display modes can be simply achieved through IEI SmartOSD software utility.
Dual portrait 2MP color mode Dual portrait 2MP grayscale mode
Dual portrait 2MP grayscale/color mode Dual portrait 2MP color/grayscale mode
Auto-Dimming for Ambient Light Adjustment
The auto-dimming function helps create better diagnostic experience under proper light condition and extend backlight lifetime
 
User Selectable Gamma Settings and Color Temperature Settings
IEI provides you with flexible Gamma settings and color temperature settings
for side-by-side image comparison in dual-viewing modes. The independent
Gamma settings (Gamma 1.8,2.0,2.2) and color temperature settings (6500K, 9300K) provides flexible display modes for images from different modalities.
 
 
100% Compatible with VESA DDC/CI Protocol
 

MMD-4300C is implemented with the VESA DDC/CI protocol and the standard VESA Monitor Control Command Set (MCCS). The universal communication interface enables remote control management through a network. The MMD-4300C allows easier two-way communications with the host PC with only a DVI cable. Additional serial or USB cables are not necessary. Through DDC/CI protocol, the software OSD manages MMD-4300C remotely including power mode control, backlight luminance reading and front sensor luminance reading. This reduces the maintenance cost for the end user. IEI also provides software OSD customization services with a command library and customer defined MSSC command programming supports for easier software development.

Various software OSD functions:
• Power on/off
• Display mode selection: 4MP/2MP, color/monochrome
• Gamma and color temperature selection
• Luminance selection
• DICOM/ Gamma Look-Up-Table selection
• Monitor Information


Built-in Front Sensor for Continuous DICOM Conformance
IEI has designed a built-in, front-mounted sensor which continually monitors
the luminance output to ensure consistent images over time.

 


Built-in Front Sensor

IPX2 Compliance
The whole enclosure of MMD-4300C is compliant with IPX2 waterproof standard. The special design for infection control enables MMD-4300C reliably used in critical care environment including the operating room.
    Specifications
PACSmate 4MP MMD-4300C
Drive System a-Si TFT active matrix Default gamma Gamma 2.2
Display area (H x V) 641.3mm x 400.8 mm LUT 10-bit for each RGB
Diagonal size of display 75.6cm (30.0 inches) USB 2.0 hub 1 upstream/ 2downstream
Resolution (H x V) 2560 x 1600 Signal input Master : Dual link DVI-D (digital)
Slave: Single link DVI-D (digital)
Display color 16,777,216 colors Membrane keypad Yes
Pixel pitch (H x V) 0.2505mm x 0.2505 mm Sub-pixel pitch (H x V) 0.0835mm x 0.2505 mm
Pixel format RGB (Red dot, Green dot, Blue dot) vertical stripe Max. Luminance (calibrated) 250cd/m2
Luminace-max. 370cd/m2 Contrast ratio 1000:1 (typical)
Backlight 16 CCFL Physical dimensions
(H x W x D)
With stand: 522mm x 736mm x 266 mm (landscape)
Without stand: 480mm x 736mm x 76 mm (landscape)
Viewing angle

Right/Left: 178

 Up/Down: 178

Power adapter
Input voltage range
100VAC-240VAC
Response time (Ton + Toff) 12ms (typical) Power adapter
Input frequency range
47Hz-63Hz
Polarizer surface/ hardness Antiglare/ 3H Power adapter
Input AC current
2.0A (max). at 90VAC
Operating temperature 10 ~ 35 Power adapter
Power output
24VDC, 6.25A, 150W (max)
Operation relative humidity 30% ~ 75%
Non-condensing
Storage temperature 0 ~ 45
Storage/ Transportation
Relative humidity
10% ~ 95%
Non-condensing
Weight (with stand) 15kg
     
     Ordering information
Part No. Description
MMD-4300C 4 megapixel, 30" color LCD monitor with IPX2 housing
MMD-4300CX 4 megapixel, 30" color LCD monitor with IPXX housing
     Packing List
Description Amount
PACSmate® Series medical LCD monitor 1
Monitor stand 1
Power cord (US x 1, EU x 1) 1
Power adapter 1
Dual-link DVI-D signal cable 1
USB cable 1
Utility CD-ROM (for user's manual and software utility) 1